| |
 |
|
|
 |
|
 |
Tel: 086-510-88551966 88550900
Fax: 086-510-88551121
URL: http://www.wxasaya.com
E-mail: asaya@wxasaya.com
Zip: 214112
Add: No.22,xihong Road, Xintai Industrial Technical,Meicun Town,Wuxi , Jiangsu , China |
|
|
|
 |
| RC PEP-Z(HV) SERIES |
- PREFAC
RC PEP-Z(HV) SERIES is designed for flame-treated PE/PP bottles. High performances and gloss finish can be obtained with reasonable price. PEP-Z(HV) is suitable for high-speed print as it cures with low integral light quantity. All colors are conformed to EN71-3.
- APPLICATIONS
Flame-treated polyethylene bottles/polypropyrene bottles.
- CHARACTERISTICS
One-component type. Excellent adhesion.
PEP-Z(HV) cures with low integral light quantity. Suitable for high-speed print.
Cured ink film is hard and resistant to scratch.
Reproducibility of fine patterns is good.
PEP-Z(HV) do not contain any harmful materials such as heavy metal or N-Vinyl Pyrrolidone. All colors are conformed to EN71-3.
- HOW TO USE
Ink is supplied in ready-to-use condition. Stir well before use.
Add PEP-Z REDUCER up to 10%, if necessary.
Add CLEAR to lower density. (Adding ratio is subject to the conditions.)
PEP-Z(HV) can be usually used without any additive. However, add JAR-18 by 5% when the adhesion is not good due to the substrate. The mixture of ink and additive has pot life and should be used up within 12 hours.
Standard curing conditions: (These conditions change depending on the substrate.)
Metal halide lamp 120W/cm, Distance from focus : 10 cm
Conveyor speed : 20 m/min (Integral light : approx.120 mJ/cm²)
Mesh : Polyester >350 meshes/inch, Thickness of sol : <10 microns
- COVERAGE
Approx. 70-90m²/kg
- COLOR RANGE
CLEAR, WHITE, OPAQUE WHITE, YELLOW, LEMON YELLOW, ORANGE, BRIGHT RED, RED, GERANIUM, PINK, VIOLET, BLUE, DEEP BLUE, SKY BLUE, MARINE BLUE, GREEN, BLACK
- TYPE OF PACKING
1kg PLASTIC CONTAINER
- PRECAUTIONS
The viscosity and printability of the ink change depending on the temperature. The printability in summertime is different from that in wintertime.
Although skin irritation is low(P.I.I:<2.0), it is advised to avoid skin contact with the ink. In case of contact with skin, wash immediately with soap and water.
Store the ink in a cool and dark place. Stir occasionally to keep stability when the ink is stored for a long time.
Stir well before use as de-foamer might be separated.
You can add JA-950H by 1-2% instead of JAR-18 when better adhesion is required. The cost can be reduced by using JA-950H, although pot life of the mixture is 4-8 hours.
Please refer to MSDS before use.
Be sure to do trial print before commercial run to confirm that the product fits the purposes.
- PHYSICAL PROPERTIES
Substrate : HDPE(Wettability is approx.72 dyn/cm by flame treatment.)
Meshes : Polyester 350 meshes/inch
Curing : One metal halide lamp 120W/cm, Air-cooling system
Conveyor speed - 20 m/min. (Integral light : 120 mJ/cm²)
| TEST ITEMS |
TEST METHODS |
RESULTS |
| Adhesion |
Cross-hatch, tape-peeling test |
100/100 Pass |
| Over-printability |
Adhesion test with 3-time-print |
Pass |
| Alcohol resistance |
Peeling test after 24-hour-immersion
in 99.5% ethanol. |
100/100 Pass |
| Warm water resistance |
Peeling test after 24-hour-immersion
in warm water of 40deg.C. |
100/100 Pass |
- Information given here is gained from our laboratory testing, and no firm guarantee is implied.
Weathering resistance depends on the color. Please refer to lightfastness chart before use. |
|
|
|
