|Tel: 086-510-88551966 88550900
Add: No.22,xihong Road, Xintai Industrial Technical,Meicun Town,Wuxi , Jiangsu , China
|3200 SERIES SIM INK
3200 SERIES SIM is two-pack type of ink designed for insert-moulding and in-mould process. 3200 SERIES dries at low temperature and produces flexible ink film with excellent heat resistance.
Polycarbonate sheet or treated PET film for insert moulding and in-mould usage. Polycarbonate and PET film for nameplates.
The ink dries at low temperature(80-90 degrees Centigrade).
Ink film is flexible and tough to cope with moulding process.
Heat resistance is excellent to be used in insert moulding or in-mould processing.
- HOW TO USE
Mix the ink, Hardener and thinner at the following ratio:
Hardener JA-930 15
PC thinner 10-30
Tack-free : 80 degreesC x 5 minutes
Minimum drying conditions : 80 degreesC x 40 minutes
Standard drying conditions : 90 degreesC x 30 minutes
Ideal drying conditions :100 degreesC x 20 minutes
- POT LIFE
Approx.8-10 hours at room temperature(20degreesC)
- STENCIL & WASHING UP
Vinyl Cleaning thinner is recommended for washing up.
- COLORS & TYPE OF PACKING
Standard 19 colors. 1kg can
JA-930 : 0.1 kg can
When SIM ink is dried at 80-90 degreesC, satisfactory heat resistance may not be obtained.
To improve heat resistance:
Dry the ink at 100 degreesC
Use Hardener JA-970 instead of JA-930 : In this case, the ink film becomes slightly harder. The pot life of the mixture is 4-5 hours.
Add accelerator, JA-E11, by 2% : The pot life of the mixture is 1-2 hours.
JA-930 becomes solid by the reaction to humidity. Keep the lid of the continer shut. Store the product in a cool and dark place. Once the container is opened, film may appear over the surface if the product is left unused for a long time. If the shelf life is still valid, the product can be used by removing the film.
The shelf life of JA-930 is one year unopened, approximately three months after the container being opened.
Please refer to MSDS before use.
Be sure to do trial print before commercial run to confirm that the product fits the purposes.
Single color printing : Standard colors are used.
Over-printing : 3201 white + 3246 blue + 3290 black
Thinner : PC thinner standard drying
Hardener : JA-930 by 15%
Substrate : Teijin Panlite Sheet 0.5mm
Mesh : 250 meshes/inch
Drying : 5 minutes for 100 degrees C during printing process & 20 minutes for 100 degrees C as final drying
||JIS K5400 pencil hardness
||JIS K5400 DuPont Impact test diameter 1/2 inch, 500grams, 30 cm
||No cracks No peeling-off|
||JIS K5400 diameter 2mm
||No cracks No peeling-off|
||100 degrees C x 72 hours
||Immersion in water of 50 degrees C for 24 hours
||60 degrees C x 95%RH x 120 hours
||-30deg.C --> 2hrs --> 80deg.C 2hrs --> 2hrs --> -30deg.C 2hrs, 30 cycles(240 hours)
||Pressed with the cloth soaked with below thinner with the load of 500 grams. The times of press before peeling-off
||ethanol:15 - 60|
gasoline:12 - 40
||Immersion in 1N H2SO4 at room temperature for 24 hours
||Immersion in 1N NaOH at room temperature for 24 hours
|3213 LEMON YELLOW
||3235 SKY BLUE
|3214 DEEP YELLOW
||3245 DEEP BLUE
|3206 BRIGHT RED
||3287 MARINE BLUE
- Grade 8 : Superb. outdoor exposure >2 years.
Grade 7 : Excellent. outdoor exposure <2 years.
Lightfastness is much degraded when clear or white is added to the standard color.
Information given here is gained from our laboratory testing, and no firm guarantee is implied.